Building the Delta Airlines Douglas DC-6 scale model - Roden, 1/144

Building the Delta Airlines Douglas DC-6


Delta Airlines Douglas DC-6  scale model

  Roden plastic scale model in 1/144 scale, kit number 304


1/144 Delta Airlines Douglas DC-6 - History

The Douglas DC-6 is a piston-powered airliner and transport aircraft built by the Douglas Aircraft Company from 1946 to 1958. Originally intended as a military transport near the end of World War II, it was reworked after the war to compete with the Lockheed Constellation in the long-range commercial transport market. More than 700 were built and many still fly today in cargo, military, and wildfire control roles.
The DC-6B, originally powered by Double Wasp engines with Hamilton Standard 43E60 constant-speed reversing propellers, was regarded as the ultimate piston-engine airliner from the standpoint of ruggedness, reliability, economical operation, and handling qualities.
Delta airlines operated the Douglas DC-6B from Dec. 01, 1948 to Dec. 11, 1968 when it was time for this legendary propeller driven airliner to make place for the jet age.

1/144 Delta Airlines Douglas DC-6 - Assembly

           I started this build from the wings. They come in three piece assembly, with single lower piece and two upper pieces. I glued those together using Humbrol’s liquid poly. The ailerons and part of the flaps are molded on the upper wing pieces resulting thin trailing edge without seam line after assembly. Another nice feature of the single piece lower wing is the molded in dihedral.
             I decided to build this model in gear up configuration and therefore felt the need for livening it up a bit. Part of my plan was to cut the flaps and place them in lowered position. Before cutting them I inserted appropriate pieces of plastic inside each wing in order to retain the structural rigidity of the original assembly. Then, using RB saws I cut the flaps. The gap between the lower and upper wing parts was filled and shaped with Milliput. The front part of the flaps was also filled with Milliput and shaped with sandpaper. To better accommodate the flaps in the wing I thinned the plastic of the upper wing substantially. Later, using a saw I created slots in the flaps to house the hinges. 

Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model

           To close the gear bays I first tried using the covers that come with the kit. The fit was very bad so instead I used Milliput again. Then I scribed the panel lines using needle in a pin vice.

Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model

Another disappointing aspect of this kit was the detail on the engine cowlings and nacelles. The intakes were blank, the radiator door was not existent so were the exhaust stacks.  To open up the intakes I used my photo etched saw then folded 800 grit sanding paper to get close to the correct shape. Having four engines, with two intakes each, was real mojo drainer. 
Next were the exhaust stacks. First I drilled a holes in the cowling and then shaped the holes and the nacelles with square file. To make the exhausts I drilled holes in lengths of circular rod then squashed them a bit with pliers to get oval shape. I cut them to desired angle then installed them in pairs in their beds. 
To represent the radiator heat outlets first I cut the plastic that was blanking this area using a saw. Then I assembled the engines, the fit was somewhat mediocre as quite a lot of dry fit and sanding was needed to get the engine faces inside the two cowling parts. After some careful trimming of the outlet opening I glued square plastic stock on the radiator side and another one on the wing side. Then I connected those walls with a sheet plastic piece creating a ramp. The radiator outlet door was also made from sheet plastic and Mr. Hobby Cement S.
 To conclude the job on the engine cowlings and nacelles I fixed some gaps along the seamlines using superglue and scribed some panel lines. After that I attached the engines to the wings. Again the fit was not very good. On the outer engines I got away with small amount of Mr. Dissolved Putty and sanding. The wheel wells are part of the inner engine pair nacelles and these nacelles were with different shape than the outer ones. Unfortunately all four engines had the same shape which lead to big step. To overcome this issue I temporarily attached the engines with drop of super glue and traced their outline on the wing part of the nacelle. Then I broke of the engines and shaped the nacelles using files. After the shape was fair enough I cemented the inner engine pair in place. Again using Mr. Dissolved Putty I blended the nacelle parts together. Same was done for the outer pair.



Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale modelDelta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale modelDelta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale modelDelta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model

           To finish the wings sub-assembly I scratch built the intake that is located almost in the center of the aircraft’s bottom.

Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model

            Now, having the wing assembly ready it was time to pay attention to the fuselage. It is divided in two, lengthwise, with the nose and the canopy being separate parts. Here the gear bay was closed using Milliput just like on the wings. The assembly was glued with Mr.Cement S. Some Mr. Dissolved putty was required on the nose joint as well as on the spinal joint. The tail was molded with the complete rudder on the left fuselage halve and this resulted in small step after I assembled the halves. I filled it with plastic strip, sanded it smooth and rescribed the panel lines. Plastic strips were also used on the nose, to correct its shape. 

Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale modelDelta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model

          Due to the fact that I removed portion of the wings to represent the dropped flaps, two significant openings needed to be blanked off. The top portion was built with Milliput prior to wings installation and the sides from plastic strips once everything was in place.

Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model  Delta Airlines Douglas DC-6  scale model

         The wings to fuselage assembly required some minor adjustments but resulted in good fit and small gaps to fill. The wing root joints were more prominent than those on the lower fuselage side. All was dealt with tinted CA glue. After sanding the results were very good. The same CA glue mixture was used to fill the joint between the horizontal stabilizers and the tail section. To finalize the assembly stage I rescribed the panel lines on the fuselage. I also used CA glue to fill various gaps on the entire model. A tutorial on how to facilitate CA glue you can find here!

Delta Airlines Douglas DC-6, 1/144  scale model  Delta Airlines Douglas DC-6, 1/144  scale model  Delta Airlines Douglas DC-6, 1/144  scale modelDelta Airlines Douglas DC-6, 1/144  scale model  Delta Airlines Douglas DC-6, 1/144  scale model  Delta Airlines Douglas DC-6, 1/144  scale modelDelta Airlines Douglas DC-6, 1/144  scale model  Delta Airlines Douglas DC-6, 1/144  scale model  Delta Airlines Douglas DC-6, 1/144  scale modelDelta Airlines Douglas DC-6, 1/144  scale model  Delta Airlines Douglas DC-6, 1/144  scale model  Delta Airlines Douglas DC-6, 1/144  scale modelDelta Airlines Douglas DC-6, 1/144  scale model  Delta Airlines Douglas DC-6, 1/144  scale model  Delta Airlines Douglas DC-6, 1/144  scale model

1/144 Delta Airlines Douglas DC-6 - Prep and paint


            The preparation of the model for the painting stage started with a good cleaning with IPA. Next I applied Mr. Surfacer 1500 diluted with Mr. Levelling Thinner. The primer gave me smooth coat with just a few spots to do some sanding on. 

Delta Airlines Douglas DC-6, 1/144  scale model Mr. Finishing Surfacer 1500   Delta Airlines Douglas DC-6, 1/144  scale model Mr. Finishing Surfacer 1500   Delta Airlines Douglas DC-6, 1/144  scale model Mr. Finishing Surfacer 1500 Delta Airlines Douglas DC-6, 1/144  scale model Mr. Finishing Surfacer 1500   Delta Airlines Douglas DC-6, 1/144  scale model Mr. Finishing Surfacer 1500

          Next step was to apply gloss white on the top of the fuselage. That was done using Mr. Color C01 diluted with Mr. Levelling thinner. This combination gives really good gloss surface. At this point I decided to try how the decals will work before I continue with the rest of the work on this scale model. 

Delta Airlines Douglas DC-6, 1/144  scale model Mr. Color C01 Mr. Leveling Thinner   Delta Airlines Douglas DC-6, 1/144  scale model Mr. Color C01 Mr. Leveling Thinner Delta Airlines Douglas DC-6, 1/144  scale model Mr. Color C01 Mr. Leveling Thinner   Delta Airlines Douglas DC-6, 1/144  scale model Mr. Color C01 Mr. Leveling Thinner

           I masked the white and proceeded towards the blue paint that covers the engine nacelles, part of the wings and part of the nose of the aircraft. I mixed my own colour trying to be as close as possible to the blue on the decals. The blue parts were subsequently masked.

Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model

                The lower surfaces of the fuselage and the complete wings (without the blue parts) are supposed to be in natural metal finis (NMF). I wanted to try to achieve some panelling effect using only one metallic shade and various underlying surfaces. I attempted marble coat with gloss black on the outer wings and on the forward and rear fuselage sections. With matt black I primed the inner wings and the center fuselage section of the aircraft. 


Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model


            The NMF paint that I used was Alclad II “Chrome for Lexan”. I applied it in several thin coats and kind of achieved the desired effect. After some masking, a layer of the alclad peeled not from the primer or from the plastic but from another layer of alclad. I had to do some sanding to get rid of the ridges and then re-applied more alclad. To finish with the NMF I sealed it with “Sealer for Metalizer” from Humbrol. For me this is the best product for sealing NMF.
        To paint the black radome I masked around it with thin masking tape and then extended the mask with masking putty.

Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model

1/144 Delta Airlines Douglas DC-6 - Decaling


            The decals are not the best I ever used. They are very hard and brittle. Furthermore they are not reacting very much to decal solutions. This time I used Mr. Mark softer Neo because I ran out of my preferred Agama Hypersol. Also the decals had some geometrical/size discrepancies with the panel lines – like the rear door position. The red line above the cockpit windows I joined using paintbrush. Finally, after the decals were in place they were sealed with Mr. Super clear III.

1/144 Delta Airlines Douglas DC-6 - Weathering

            
           There is not so much weathering on this aircraft but as any operational machine some dirt and grime accumulate during its work. I airbrushed exhaust stains after the exhaust stacks and made some streaks after the hinges on the ailerons and flaps. Also I did some post shading on the lower, front panel lines of the fuselage with much thinned black paint. The idea was to have the post shading on the forward edge of each panel. For this I masked along each panel line and sprayed a faint “dirt” toward the rear of the aircraft.

1/144 Delta Airlines Douglas DC-6 - Display base


              The display base is comprised of several products. First there is the plastic display stand that comes as Zvezda kit Nr: 2735. That was painted with AK 480 Extreme Metal “Dark Aluminium”. Then we have a cheap photo frame. And finally there is a part of contemporary brochure issued by Delta airlines. Putting those together gave nice overall appearance in inflight configuration.   


Delta Airlines Douglas DC-6, 1/144  scale model

Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model Delta Airlines Douglas DC-6, 1/144  scale model   Delta Airlines Douglas DC-6, 1/144  scale model

That's all for this build, stay tuned for more and subscribe to my YouTube channel
Best Regards and happy modeling
Metodi Metodiev


 Plastic scale model inbox reviews.   Plastic scale model build articles   Plastic scale model building tutorials.
>

4 comments:

  1. Yes i am totally agreed with this article and i just want say that this article is very nice and very informative article.I will make sure to be reading your blog more. You made a good point but I can't help but wonder, what about the other side? !!!!!!Thanks Gebäudereinigung Adelebsen

    ReplyDelete
  2. This was really an interesting topic and I kinda agree with what you have mentioned here! Treppenhausreinigung Einbeck

    ReplyDelete
  3. I was surfing net and fortunately came across this site and found very interesting stuff here. Its really fun to read. I enjoyed a lot. Thanks for sharing this wonderful information. Unterhaltsreinigung Hardegsen

    ReplyDelete